Filter by
All
Resources
Case Studies
Blog
FAQs
Is installing ICFs a DIY project?
Fox Blocks rec­om­mends that all installers using Fox Blocks ICFs com­plete a Fox Blocks train­ing pro­gram to ensure they have a bet­ter under­stand­ing of the basics. How­ev­er, for first time installers, it is pre­ferred that a Fox Blocks trained, expe­ri­enced installer inspect the instal­la­tion pri­or to place­ment of con­crete and assist in the place­ment of the con­crete, as they are famil­iar with work­ing with con­crete and can ensure the build is struc­tural­ly sound and safe and the walls are con­sol­i­dat­ed prop­er­ly, built straight and plumb.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
How do frame in openings?
Fox Blocks has devel­oped the Fox Buck specif­i­cal­ly to frame open­ings such as win­dows and doors. The Fox Buck pro­vides insu­la­tion around the open­ing plus sup­port for the attach­ment of the win­dow or door.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
What is the typical Interior finish on an ICF?

All build­ing codes in the USA and Cana­da spec­i­fy that plas­tic insu­la­tion (EPS) must be cov­ered by a ther­mal bar­ri­er equiv­a­lent to 15 min­utes of fire pro­tec­tion in hab­it­able spaces. This is achieved with ½” gyp­sum board or an equiv­a­lent mate­r­i­al. Fox Blocks has spe­cif­ic fire test­ing that proves reg­u­lar ½” gyp­sum board with reg­u­lar dry­wall screws fas­tened into the plas­tic webs remains on the wall for the required 15-minute time peri­od.

VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
Is burning EPS toxic?
Test reports con­duct­ed by the Nation­al Research Coun­cil state: ​“The max­i­mum tox­i­c­i­ty index obtained from the com­bus­tion of poly­styrene was of the same order as that of wood.” Fox Blocks ICFs have been test­ed to meet build­ing code require­ments for flame spread rat­ings, smoke devel­op­ment and tox­i­c­i­ty
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
Can the plastic webs be detected by using stud finders?

A stud find­er typ­i­cal­ly uses the den­si­ty of mate­ri­als to locate studs. The polypropy­lene (plas­tic) web mate­r­i­al will show up on high qual­i­ty den­si­ty stud find­ers. Note, the webs in Fox Blocks are spaced at 8″ (200 mm) on cen­ter and will be con­tin­u­ous ver­ti­cal­ly on each side of the wall.

VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
Can I install a 16' garage door and / or large openings in a concrete wall?
Yes, if the fol­low­ing cri­te­ria is avail­able for the design of a con­crete lin­tel (beam) over the open­ing – con­crete lin­tel depth min­i­mum 16″ (400 mm) or more with no point loads. Larg­er open­ings would require an engi­neered design.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
What size and how much steel reinforcement is required in an ICF?

Fox Blocks walls are designed as rein­forced con­crete walls, with steel rein­force­ment bars spec­i­fied to be installed ver­ti­cal­ly and hor­i­zon­tal­ly, as the walls are built. Typ­i­cal rein­force­ment bar sizes used are #4 or #5 (10 m or 15 m).

VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
What exterior finishes can be used on an ICF?
Fox Blocks are com­pat­i­ble with all exte­ri­or fin­ish mate­ri­als and sys­tems – sid­ing, stuc­co, mason­ry veneer, sim­u­lat­ed stone, etc. The attach­ment of cer­tain exte­ri­or fin­ish­ing sys­tems is rec­om­mend­ed with exte­ri­or grade screws fas­tened into the exposed or con­cealed webs.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
Do I need an engineer to design and stamp Fox Blocks building plans?
Fox Blocks are list­ed in the build­ing codes (IRC- Sec­tions R404, R611 or NBCC Part 9) with spe­cif­ic applic­a­bil­i­ty lim­its for res­i­den­tial con­struc­tion. If the project meets the applic­a­bil­i­ty lim­its with­in the build­ing code, a Pro­fes­sion­al Engi­neer may not be required (depen­dent on local build­ing depart­ment require­ments). A build­ing offi­cial has the right to request engi­neer­ing and in some regions all projects require a professional’s stamp. For any projects that exceed the applic­a­bil­i­ty lim­its, a Pro­fes­sion­al Engi­neer is required for the struc­tur­al design. Check with your local build­ing depart­ment.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow
Is there a top and bottom on the blocks when installing the Fox Blocks forms?
Fox Blocks forms have a reversible inter­lock sys­tem on all blocks. The robust inter­lock allows the blocks to fit togeth­er very tight­ly, elim­i­nat­ing any require­ment for adhe­sives. A reversible inter­lock speeds up the instal­la­tion.
VIEW PAGE
Arrow1 right shadowLong arrow right with shadow